Back to home

Product guides / Get started

Product guides / Get started

Pulse Meter and App

Get started with the Bluelab Pulse Meter

FAQ for the Bluelab Pulse Meter

Troubleshooting Bluelab Pulse Meter connectivity problems

Configure Pulse to medium type, nutrient range and moisture range

How to calibrate the Bluelab Pulse Meter [+ video]

What if I can't see my Pulse on the "Select Device" list?

Understanding Nutrient Measurements with the Pulse Meter

How do I give feedback on the Pulse app or request new features?

Where is the Pulse measurement being taken from?

Why are the conductivity measurements from my Pulse Meter different from my normal extraction tests?

Does the Custom Media function of the Bluelab Pulse only calibrate the moisture content?

Why can't I set my Pulse conductivity units to ppm?

Why do the lights on the Pulse flash a few times before going solid?

What maintenance is required for the Bluelab Pulse Meter?

How do you turn the Pulse Meter on/off?

Does the Bluelab Pulse Meter always measure all three readings; moisture, conductivity and temperature?

I have just replaced my Pulse Meter battery but it keeps on restarting. How do I get it to run?

Why does the Pulse app show “Stabilising” whenever a measurement is taken?

Which base medium do I use on my Pulse app?

With the Pulse Meter and app, how long will it take to create a custom calibrated medium?

Is all my Pulse device data backed up?

Why does the status bar on the measurement screen of my Pulse app say “Not Connected”?

How accurate is the Bluelab Pulse Meter?

How do I export my Pulse app data?

Why can’t the Pulse app see my Pulse meter after pairing with it through Android/iOS?

Do I need to calibrate the Bluelab Pulse Meter?

How do I see what the settings were when a Pulse measurement was taken?

How to take a measurement with the Bluelab Pulse Meter [+ video]

See more

Leap pH Probe

FAQ's for the Leap pH Probe

Connect Stick 2

Connect Stick can't be detected - "Detecting Connect stick..." Resolution 1: Installing driver

Connect Stick can't be detected - "Detecting Connect stick..." Resolution 2: Enable the virtual COM port

Connect Stick can't be detected - "Detecting Connect stick..." Resolution 3: Update the driver

Bluelab Connect Stick 2 & Range Extender 2 - Setup

Combo Meter

Getting Started: The Bluelab Combo Meter

Combo Meter Conductivity and pH Probe Cleaning and Calibration - video

pH Pen

Getting started: The Bluelab pH Pen

FAQ and troubleshooting for the Bluelab pH Pen and Bluelab Soil pH Pen

How to take a measurement with the Bluelab pH Pen

How to disinfect Bluelab products during COVID-19

Soil pH Pen

Getting started: The Bluelab Soil pH pen

How to operate the Bluelab Soil pH Pen

Truncheon Nutrient Meter

FAQ and troubleshooting for the Bluelab Truncheon Nutrient Meter

Getting started: The Bluelab Truncheon Nutrient Meter

PeriPod

Bluelab PeriPod Dosing Pump Size Selection Guide

pH Controller

Getting Started: The Bluelab pH Controller

pH Controller Acid/Alkaline Strength Recommendations

Conductivity Pen

Getting started: The Bluelab Conductivity Pen

FAQ and troubleshooting for the Bluelab Conductivity Pen

pH Probe

Getting Started: The Bluelab pH Probe

Care kit

Getting started: The pH and Conductivity care kit

Sample Tube and Fitting

Getting started: Bluelab Sample Tube

Replacement probes

Getting started: The Bluelab pH In-line probe

Getting Started: The Bluelab Temperature Probe

Getting Started: Bluelab Leap pH Probe

Combo Meter Plus

Getting Started: The Bluelab Combo Meter Plus

Multimedia pH Meter

Getting started: The Bluelab Multimedia pH Meter

Growers Toolbox

Getting started: Grower's Toolbox

Guardian

Getting Started: The Bluelab Guardian Monitor